@article { author = {Shajari, Yazdan and Seyedraoufi, Zahra Sadat and Razavi, Seyed Hosein and Nasri, Mehdi and Khiabani, Arash}, title = {Effect of Remelting and Standard Heat Treatment on Microstructure ‎and ‎Mechanical Properties of IN738LC Superalloy}, journal = {Founding Research Journal}, volume = {4}, number = {2}, pages = {99-109}, year = {2020}, publisher = {Iranian Foundrymen's Society}, issn = {2588-5367}, eissn = {2588-5359}, doi = {10.22034/frj.2020.238339.1122}, abstract = {In the present study, IN738LC superalloy ingot was re-melted and cast, then heat treated under ‎standard conditions. Microstructural studies with field emission scanning electron microscopy ‎‎(FESEM) equipped energy dispersive spectroscopy (EDS) showed that after re-melting and ‎controlled casting, the amount of porosity and size of γ' precipitates decreases. Also, with ‎applying the standard heat treatment cycle, the primary γ' precipitates less than 1µm in size and ‎cubic morphology and nano‏spherical‏ ‏secondary γ' precipitates appeared and eutectic γ-γˈ ‎regions were completely eliminated. Vickers hardness test results under a load of 10 Kg showed ‎that the lowest hardness is related to the solutionized sample due to remove the coarsened γ' ‎precipitates and the highest hardness (833 H.V.) is obtained after aging. According to the results ‎of the tensile test at ambient and 750◦C temperatures, by re-melting and applying the standard ‎heat treatment due to structural modification, strength and elongation increased at both ambient ‎temperature and 750◦C. Also, with applying the standard heat treatment, failure mechanism of ‎IN738LC superalloy was transferred from brittle trans-dendritic failure to brittle inter-dendritic ‎failure with little footprints of ductile fracture.‎}, keywords = {IN738LC,Re-melting,Heat treatment,Microstructure,Strength}, title_fa = {تغییرات ریزساختار و خواص مکانیکی سوپرآلیاژ IN738LC در طول ذوب مجدد و عملیات حرارتی استاندارد}, abstract_fa = {در تحقیق حاضر، شمش اولیه سوپرآلیاژ ‏IN738LC‏ مجدداً ذوب و ریخته‌گری شد و سپس تحت عملیات حرارتی استاندارد قرار ‏گرفت. بررسی‌های ریزساختاری با میکروسکوپ الکترونی روبشی گسیل میدانی ‏‎(FESEM)‎‏ مجهز به شناساگر عناصر با تفکیک ‏انرژی ‏‎(EDS)‎‏ نشان داد که پس از ذوب مجدد و ریخته‌گری کنترل شده، میزان تخلخل و اندازه رسوبات 'γ کاهش می‌یابد. ‏همچنین با انجام عملیات حرارتی استاندارد، رسوبات 'γ اولیه با اندازه زیر ‏‎µm‎‏1 و مورفولوژی مکعبی و رسوبات 'γ ثانویه کروی در ‏محدوده نانومتری نمایان شدند و مناطق 'γ-γ یوتکتیک به‌طور کامل از بین رفت. نتایج سختی سنجی ویکرز تحت بار 10 کیلوگرم ‏نشان داد که کمترین سختی به جهت حذف رسوبات مربوط به نمونه انحلال یافته است و بیشترین سختی (‏HV‎‏ 833) پس از ‏پیرسازی حاصل می‌شود. بر اساس نتایج آزمایش کشش در دمای محیط و 750 درجه سانتی‌گراد، با انجام ذوب مجدد و اعمال ‏عملیات حرارتی استاندارد به جهت اصلاح ساختار، استحکام و ازدیاد طول در هر دو دمای محیط و 750 درجه سانتی‌گراد افزایش ‏یافت. همچنین با اعمال عملیات حرارتی استاندارد، مکانیزم شکست سوپرآلیاژ ‏IN738LC‏ در دمای 750 درجه سانتی‌گراد از ‏شکست ترد درون دندریتی به شکست ترد با نشانه‌های کمی از شکست نرم بین دندریتی تغییر یافت.‏}, keywords_fa = {IN738LC,ذوب مجدد,عملیات حرارتی,ریزساختار,استحکام}, url = {https://www.foundingjournal.ir/article_113389.html}, eprint = {https://www.foundingjournal.ir/article_113389_8538b6f391c645833c1f493fe544eac8.pdf} }