@article { author = {almasi, ali and Kianvash, Abbas and Tutunchi, Abolfazl}, title = {Comparison of Ti and Nb Microalloy Addition on the Microstructure and ‎Mechanical Properties of a Quenched-Partitioned Cast Steel}, journal = {Founding Research Journal}, volume = {5}, number = {1}, pages = {31-40}, year = {2021}, publisher = {Iranian Foundrymen's Society}, issn = {2588-5367}, eissn = {2588-5359}, doi = {10.22034/frj.2021.284913.1135}, abstract = {In the present study, the effect of Ti and Nb microalloying elements on the microstructure and mechanical properties of the quench-partitioned (Q-P) steel was investigated. The samples containing Ti and Nb micro-alloying elements were subjected to Q-P heat treatment and quench-Tempering (Q-T). After Q-P and Q-T heat treatment, the properties of the samples were examined by scanning electron microscopy (SEM), X-ray analysis (XRD), microhardness, tensile tests and. The results showed that Q-P heat treatment of both sample has better mechanical properties compared to Q-T heat treatment. In the Q-P heat treatment, the plasticity of the sample containing Ti microalloy is higher than that of the Nb microalloy sample. In the Q-P heat treatment, the amount of retained austenite (γR) for the sample containing Ti is higher than that of the sample containing Nb. Fracture strength and strain of the sample containing Ti were recorded 1070 MPa and 24%, respectively. The fracture strength and strain of the sample containing Nb were also recorded 980 MPa and 19%, respectively.}, keywords = {Quench-Partitioning,Residual Austenite,tensile strength,Microalloy}, title_fa = {مقایسه تاثیر عناصر افزودن میکروآلیاژ Ti و Nb بر ریزساختار و خواص مکانیکی یک فولاد ریختگی با عملیات حرارتی تندسرمایی - بخش بندی شده (Q-P)}, abstract_fa = {در مقاله حاضر تاثیر عناصر میکروآلیاژ Ti و Nb بر ریزساختار و خواص مکانیکی یک فولاد استحکام بالا (AHSS ) در عملیات حرارتی تندسرمایی بخش بندی (Q-P ) بررسی شد. نمونه های فولادی حاوی عناصر میکروآلیاژ Ti و Nb تحت عملیات حرارتیQ-P و سرمایش سریع ، برگشت (Q-T ) قرار گرفتند. پس از انجام عملیات حرارتی Q-P و Q-T، بررسی خواص نمونه ها توسط میکروسکوپ الکترونی روبشی(SEM) ، آنالیز اشعه ایکس (XRD)، ریزسختی‌سنجی، آزمایش کشش و آزمون اریکسون انجام شد. نتایج به دست آمده نشان داد که عملیات حرارتیQ-P نسبت به عملیات حرارتی Q-T از خواص مکانیکی بهتری برخوردار است. در عملیات حرارتیQ-P حاوی میکروآلیاژ Ti، میزان آستنیت باقیمانده (γ_R) نمونه نسبت به نمونه حاوی میکروآلیاژ Nb بیشتر است. استحکام وکرنش شکست نمونه حاوی میکروآلیاژ Ti به ترتیب MPa 1070 و 24 درصد گزارش شد. استحکام و کرنش شکست نمونه حاوی میکروآلیاژ Nb نیز به ترتیب MPa 980 و 19 درصد گزارش شد. در عملیات حرارتی Q-P، شکل پذیری نمونه حاوی میکروآلیاژ Ti نسبت به نمونه میکروآلیاژ Nb بیشتر می باشد.}, keywords_fa = {کوئنچ - بخش بندی(Q-P),آستنیت باقی مانده,استحکام تسلیم,استحکام کششی نهایی,میکروآلیاژ}, url = {https://www.foundingjournal.ir/article_132846.html}, eprint = {https://www.foundingjournal.ir/article_132846_1cbcfde3bc515b743a22058a110409fe.pdf} }