@article { author = {Sanjari, Alireza and Moazami-Goudarzi, Mohammad and Khodabandeh, Alireza}, title = {Effect of Sample Diameter and Withdrawal Rate on Microstructure and Hot ‎Tensile Behavior of ‎Directionally Solidified PWA 1483 Superalloy}, journal = {Founding Research Journal}, volume = {3}, number = {3}, pages = {175-185}, year = {2019}, publisher = {Iranian Foundrymen's Society}, issn = {2588-5367}, eissn = {2588-5359}, doi = {10.22034/frj.2019.194045.1094}, abstract = {Microstructure and mechanical properties of a PWA 1483 superalloy directionally solidified in a Bridgman furnace are investigated. The effects of sample diameter, i.e. 13, 33 and 55 mm, and withdrawal rate, i.e. 1.5, 3 and 4.5 mm/min, on primary dendrite arm spacing were evaluated using standard metallographic techniques. Morphology and size of different microstructural constituents were studied by the scanning electron microscopy. Hot tensile tests at 850 °C was utilized to evaluate the mechanical properties of the heat treated samples. While primary dendrite arm spacing decreased with increasing withdrawal rate, it increased with increasing sample diameter. The cubic gamma prime precipitates formed in the interdendritic region were smaller than those formed in the dendrite core. The hot tensile strength of aged samples increased with reduced sample diameter and increased withdrawal rate. In addition, the reduction of sample diameter resulted in increasing of the hot ductility. However, the tensile ductility did not change significantly with the withdrawal rate.}, keywords = {PWA 1483 superalloy,Directional Solidification,Dendrite arm spacing,Gamma prime precipitates,hot tensile strength}, title_fa = {تاثیر قطر نمونه و سرعت بیرون کشی بر ریزساختار و خواص کششی گرم سوپرآلیاژ PWA 1483 انجماد جهتدار شده}, abstract_fa = {در تحقیق حاضر، ریزساختار و خواص مکانیکی حاصل از انجماد جهت‌دار سوپرآلیاژ ‏PWA 1483‎‏  در یک ‏کوره بریجمن مطالعه شده است. به این منظور نمونه‌هایی با قطر 13، 33 و 55 میلیمتر در سرعت‌های بیرون‌‏کشی 5/1 تا 5/4 میلیمتر بر دقیقه تولید و فاصله بین بازوهای دندریت‌های اولیه پس از متالوگرافی نمونه-‏های ریخته شده تعیین شد. مورفولوژی و اندازه اجزاء مختلف ریزساختاری با استفاده از مطالعات ‏میکروسکوپی الکترونی بررسی شد. خواص مکانیکی هر یک از نمونه‌های ریخته شده پس از عملیات ‏پیرسازی و با استفاده از آزمایش کشش گرم در دمای 850 درجه سانتیگراد ارزیابی شد. نتایج نشان داد که ‏با افزایش سرعت بیرون‌کشی و کاهش قطر نمونه فاصله بین دندریت‌ها کاهش می‌یابد. ذرات گاما پرایم ‏تشکیل شده در فضای بین دندریتی کوچکتر از رسوب‌های تشکیل شده در هسته دندریت بودند. استحکام ‏کششی گرم نمونه‌های تولید شده با کاهش قطر نمونه و افزایش سرعت بیرون‌کشی افزایش یافت. علاوه بر ‏این، کاهش قطر موجب افزایش انعطاف‎‌پذیری گرم نمونه‌های تولیدی شد. با این وجود، با تغییر سرعت ‏بیرون کشی، تغییر محسوسی در انعطاف‎‌‎پذیری مشاهده نشد.‏}, keywords_fa = {سوپرآلیاژ PWA 1483,انجماد جهت دار,فاصله بازوهای دندریتی,اندازه رسوب های گاماپرایم,استحکام کششی گرم}, url = {https://www.foundingjournal.ir/article_93107.html}, eprint = {https://www.foundingjournal.ir/article_93107_1b70735068ae75a1558f3b2a09bf5548.pdf} }