@article { author = {Saffari, Elaheh and Taghiabadi, Reza}, title = {An Investigation on the Effect of Chill Modification on Microstructure and ‎Quality Index of Al-15Mg2Si Composite}, journal = {Founding Research Journal}, volume = {4}, number = {2}, pages = {79-87}, year = {2020}, publisher = {Iranian Foundrymen's Society}, issn = {2588-5367}, eissn = {2588-5359}, doi = {10.22034/frj.2020.210848.1112}, abstract = {Cast Al-15Mg2Si composites due to appropriate specific strength and tribological properties are ‎widely used in automotive and aerospace industries. The improved properties of these composites ‎are governed by the correct controlling of morphology, size, and distribution of primary Mg2Si ‎particles. In this study the effect of solidification cooling rate (chill modification) was investigated ‎on structure and quality index of Al-15Mg2Si composite. The casting operation was performed in ‎different molds with varying cooling rates of 2.7, 5.5, 17.1, and 57.5 °C/s. According to the ‎microstructural observation and image analysis results, increasing the solidification rate resulted in ‎refinement of primary Mg2Si particles and improvement of their distribution in the matrix. The ‎increased solidification cooling rate, moreover, refined the grains so that increasing cooling rate ‎from 2.7 to 57.5 °C/s resulted in 93% reduction in grain size. These microstructural variations ‎improved the composite tensile strength, fracture strain, and quality index. The quality index of ‎composite solidified at 2.7 °C/s was found to be lower than that of composite solidified at cooling ‎rate of 57.5 °C/s by 240%.}, keywords = {Composite,Al-Mg2Si,Chill modification,tensile properties,Quality index}, title_fa = {بررسی تاثیر بهسازی تبریدی بر ریزساختار و اندیس کیفیت کامپوزیت Al-15Mg2Si}, abstract_fa = {کامپوزیت‌های ‏Al-Mg2Si‏ به‌دلیل استحکام ویژه مناسب و خواص تریبولوژیکی عالی در صنایع خودروسازی و هوا-فضا مورد ‏استفاده قرار می‌گیرند. دست‌یابی به خواص برتر در این کامپوزیت‌ها، مستلزم کنترل صحیح مورفولوژی، ابعاد و نحوه توزیع ‏ذرات ‏Mg2Si‏ در زمینه است. در این تحقیق، تاثیر افزایش سرعت انجماد (بهسازی تبریدی) بر ساختار و اندیس کیفیت ‏کامپوزیت ‏Al-15Mg2Si‏ بررسی شده است. عملیات ریخته‌گری نمونه‌های کامپوزیتی در قالب‌های مختلف با سرعت انجماد ‏متوسط متفاوت (7/2، 5/5، 1/17 و ‏ 5/57 درجه سانتیگراد بر ثانیه) انجام شد. بر اساس نتایج مطالعات ریزساختاری و آنالیز تصویری، با ‏افزایش سرعت انجماد، ابعاد ذرات بین‌فلزی ‏Mg2Si‏ کاهش یافته و توزیع ذرات در زمینه بهبود می‌یابد. افزایش سرعت ‏انجماد علاوه بر این موجب افزایش سختی زمینه و کاهش اندازه دانه‌ها می‌شود به‌گونه‌ای که با افزایش سرعت انجماد از 7/2 ‏به ‏5/57 درجه سانتیگراد بر ثانیه اندازه متوسط دانه‌ها حدود 93 درصد کاهش می‌یابد. این تغییرات ساختاری موجب بهبود استحکام کششی، ‏درصد ازدیاد طول و در نتیجه اندیس کیفیت کامپوزیت می‌شود. اندیس کیفیت نمونه منجمد شده تحت سرعت ‏5/57 ‏ درجه سانتیگراد بر ثانیه حدود 240 درصد بیش از مقدار مربوطه در کامپوزیت منجمد شده تحت سرعت  7/2 درجه سانتیگراد بر ثانیه است. ‏}, keywords_fa = {کامپوزیت,Al-15Mg2Si,بهسازی تبریدی,خواص کششی,اندیس کیفیت}, url = {https://www.foundingjournal.ir/article_102505.html}, eprint = {https://www.foundingjournal.ir/article_102505_49333a2d369b238840d8407233015d6f.pdf} }