@article { author = {Yari Dehkaboudi, Ali and Tavakoli, Rouhollah}, title = {Optimum design of sprue well using computer simulation and experimental study}, journal = {Founding Research Journal}, volume = {4}, number = {2}, pages = {119-126}, year = {2020}, publisher = {Iranian Foundrymen's Society}, issn = {2588-5367}, eissn = {2588-5359}, doi = {10.22034/frj.2020.226556.1116}, abstract = {The optimal design of sprue well in of aluminum sand casting process is considered ‎in the present study. The lack of is appropriate design for this component of gating ‎system could cause filling defects such as sand erosion, oxide films and gaseous ‎bubbles trap within the melt. In this study, formerly suggested designs in the ‎literature are firstly examined and then a new optimal design, based on logical try-‎and-error using computer simulation, is introduced to avoid their limitations. The ‎performance of new design is compared to former ones by means of computer ‎simulation. Finally, to validate simulation results, experimental studies are conducted ‎using water and molten metal fluid flow in side transparent sand mold. A high speed ‎camera is employed to capture the fluid flow pattern in the transparent mold. The ‎reasonable agreement between experimental results and computational ones support ‎the validity of numerical simulation and feasibility of presented new design.‎‎}, keywords = {Optimal design,Sprue well,Sand erosion,Gaseous bubbles,Simulation}, title_fa = {طراحی بهینه حوضچه پای راهگاه بوسیله شبیه سازی کامپیوتری و آزمایش عملی}, abstract_fa = {‎در این پژوهش، طراحی حوضچه پای راهگاه در ریخته‌گری آلومینیم 356‏A‏ در قالب‌‏های ماسه‌ای مورد بررسی قرار گرفت.‏‎ ‎عدم طراحی صحیح این قسمت از سیستم راهگاهی‏‏ می‌‏تواند باعث ایجاد عیوبی چون ماسه شویی، حبس‎ ‎حباب‌های گازی و‎ ‎به دام افتادن لایه‌های اکسیدی ‏سطحی در مذاب شود. در این تحقیق، ابتدا طرح‌های پیشنهادی در مراجع مورد بررسی قرار ‏گرفتند. سپس بر اساس نتایج بدست آمده، طرح جدید سیفونی شکلی پیشنهاد شد. جهت ‏ارائه طرح بهینه از سعی و خطا روی طراحی و بررسی عملکرد توسط شبیه‌سازی کامپیوتری ‏استفاده شد. در نهایت، عملکرد طرح جدید توسط شبیه‌سازی کامپیوتری و آزمایش عملی مورد ‏بررسی قرار گرفت. در آزمون عملی از یک قالب ماسه‌ای استفاده شد که یک وجه آن جهت تصویربرداری با ‏شیشه شوک‌پذیر پوشانده شده است. الگوی پر شدن این قالب با مایع رنگی و ‏مذاب آلومینیم تصویربرداری شد. بررسی نتایج شبیه‌سازی و آزمون عملی عملکرد مناسب ‏طراحی پیشنهاد شده را تایید کرد. به علاوه، این بررسی نشان داد که نتایج شبیه‌سازی کامپیوتری و ‏آزمایش عملی تطابق خوبی با یکدیگر دارند.‏}, keywords_fa = {طراحی بهینه,حوضچه پای راهگاه,ماسه شویی,حباب‌های گازی,شبیه سازی}, url = {https://www.foundingjournal.ir/article_113390.html}, eprint = {https://www.foundingjournal.ir/article_113390_3d63082745409b4fdc87c2abe2b9cb9e.pdf} }