@article { author = {Vahdat, Seyed Ebrahim and Karimifar, Sina and Kalvand, Hamed}, title = {Properties of SAE660‎‏ ‏Bronze Bearing at Four Different Casting Conditions}, journal = {Founding Research Journal}, volume = {2}, number = {2}, pages = {89-100}, year = {2018}, publisher = {Iranian Foundrymen's Society}, issn = {2588-5367}, eissn = {2588-5359}, doi = {10.22034/frj.2018.144061.1047}, abstract = {The goal of this research is an investigation on the effect of 2 parameters of casting process including cooling rate of mold and pouring temperature on the 2 important characterization including Vickers hardness and wear resistance via pin on disc of bearing bronze SAE660. The melting had done by transistor induction furnace and then, pouring had done in sand mold in four different casting conditions, including pouring temperatures of 950C and 1200C, and cooling with water and air and finally, the microstructure via scanning electron microscopy, Vickers hardness and wear resistance via pin on disc of the SAE660 bronze had compared. The results indicated that the effect of pouring temperature can be ignored for wear resistance but the minimum weight loss due to wear via pin on disc (or maximum wear resistance) obtained when the samples cooled with air compared to water cooling, because the contents of lead, intermetallic compounds and the phase of solid solution is more in the samples cooled with air compared to water cooling. In addition, maximum hardness obtained for low pouring temperature.}, keywords = {Microstructure,Bearing,Pouring,Foundry,Casting}, title_fa = {خواص برنز یاتاقان SAE660 در چهار شرایط ریختگی متفاوت}, abstract_fa = {در این پژوهش، اثر دو متغیر دمای بارریزی و سرعت خنک‌کاری قالب در فرآیند ریخته‌گری در ماسه بر سختی و مقاومت به سایش برنز یاتاقان SAE660مطالعه شده است. مذاب برنز SAE660در کوره القایی ترانزیستوری تهیه‌شده و سپس ریخته‌گری آن در قالب ماسه‌ای در چهار شرایط متفاوت شامل دماهای ذوب‌ریزی 950 و 1200 درجه سانتی‌گراد و خنک‌کاری قالب با آب و هوا انجام شده است. ریزساختار با میکروسکوپ الکترونی روبشی، سختی به روش ویکرز و مقاومت به سایش به روش پین روی دیسک ارزیابی شده است. نتایج حاکی از این است که اثر دمای ذوب‌ریزی روی مقاومت به سایش، قابل صرف‌نظر کردن است اما کمترین کاهش جرم (یا بیشترین مقاومت به سایش) برای نمونه‌هایی است که قالب آنها در هوا خنک شده است زیرا در این نمونه‌ها، مقدار فازهای سرب، محلول جامد و ترکیب بین فلزی بیشتر است. به‌علاوه، نمونه‌هایی که دمای بارریزی آنها کمتر بوده است، سختی بالاتری داشتند. }, keywords_fa = {ریزساختار,یاتاقان,ذوب ریزی,ریخته گری,بارریزی}, url = {https://www.foundingjournal.ir/article_70395.html}, eprint = {https://www.foundingjournal.ir/article_70395_a2cd4fe14d3a591334ed0ee257a31d18.pdf} }