@article { author = {Shajari, Yazdan and Razavi, Seyed Hosein and Seyedraoufi, Zahra-Sadat}, title = {Effect of Solution Heat Treatment Media on Microstructure and Hardness of Ni-Base Superalloy IN738LC}, journal = {Founding Research Journal}, volume = {2}, number = {3}, pages = {161-179}, year = {2018}, publisher = {Iranian Foundrymen's Society}, issn = {2588-5367}, eissn = {2588-5359}, doi = {10.22034/frj.2018.155851.1061}, abstract = {In this paper, effect of solution heat treatment media of IN738LC superalloy on the microstructure and hardness was investigated. Two solution heat treatment medias were selected, solubilizing in the normal or conventional furnace, and solubilizing in the salt base. For this purpose, the samples were solubilized in a temperature range of 1090-1200°C for 20-30 minutes in normal condition and 10-12 minutes in the salt bath, and then aged at 248°C in 850°C. The results of the scanning electron microscope (SEM) and field emission scanning electron microscope (FESEM) showed that increasing the heating rate improves the solution process, and with increasing the temperature and time, the volume fraction of 'γ precipitates decreased by 26% in normal condition and 29% in salt bath. The size of the residual 'γ precipitates after solution in the salt bath is smaller than normal state, and at high temperatures, due to the activation of the aggregation mechanisms, the size and volume fraction of residual precipitates in the salt bath increased compared to the normal condition. Solution in the salt bath reduced the size of the primary'γ compared to the normal condition and increased the volume fraction of the secondary 'γ after the aging. After aging, the total volume fraction of precipitates increased by about 30% and 40%, respectively, in the normal condition and in salt bath. The results showed that the secondary 'γ precipitates are about 16nm smaller than usual and the hardness of the alloy is strongly influenced by the characteristics of 'γ precipitates and the variables of the solution treatment. Increasing the heating rate at the solution resulted in a further increase in hardness after aging and a further reduction in hardness after solution, and in both conditions increasing temperature and time of solution reduced the hardness of the samples after solution and increased after aging.}, keywords = {IN738LC superalloy,Solution,Salt Bath,Heating rate,Gama prime Precipitates}, title_fa = {اثر محیط عملیات حرارتی انحلالی بر ریزساختار و سختی سوپرآلیاژ پایه نیکل ‏‎ IN738LC}, abstract_fa = {در این پژوهش، اثر محیط عملیات انحلالی بر ریزساختار و سختی سوپرآلیاژ IN738LC مورد بررسی قرار گرفته است. عملیات انحلالی به دو صورت عادی در کوره معمولی و در حمام نمک انتخاب شد.  به­ همین ­منظور، عملیات انحلالی در بازه دمایی °C1200-1090 به­مدت 30 تا120 دقیقه برای نمونه‌ها در شرایط عادی و به مدت 10 تا 120 دقیقه برای نمونه‌های در حمام نمک انجام شد. سپس در °C850 به­مدت 24 ساعت پیرسازی شدند. نتایج میکروسکوپ الکترونی روبشی (SEM) و الکترونی روبشی نشر میدانی (FESEM) نشان داد که افزایش نرخ گرمایش روند انحلال را بهبود می‌بخشد و با افزایش دما و زمان، کسر حجمی رسوبات 'γ به­میزان 26 درصد در شرایط عادی و 29 درصد در حمام نمک کاهش یافت. اندازه رسوبات 'γ باقیمانده پس از انحلال در حمام نمک کوچک‌تر از حالت عادی است و در دماهای بالا به جهت فعال شدن مکانیزم‌های الحاق، اندازه و کسر حجمی رسوبات باقیمانده در حمام نمک نسبت به شرایط عادی افزایش یافت. انحلال در حمام نمک باعث کاهش اندازه 'γ اولیه نسبت به شرایط عادی و افزایش کسر حجمی 'γ ثانویه پس از پیرسازی شد. پس از پیرسازی، کسر حجمی کلی رسوبات حدود 30 درصد و 40 درصد به­ترتیب در شرایط عادی و حمام نمک افزایش یافت. نتایج نشان داد نانو رسوبات 'γ ثانویه درحدود nm 16 کوچک‌تر از حالت معمول هستند و سختی آلیاژ شدیدا تحت تاثیر مشخصه‌های رسوبات 'γ و متغیرهای عملیات انحلال است. افزایش نرخ گرمایش در انحلال منجر به افزایش بیشتر سختی پس از پیرسازی و کاهش بیشتر سختی پس از انحلال شد و در هر دو شرایط، افزایش دما و زمان انحلال، سختی نمونه­ها را پس از انحلال کاهش و بعد از پیرسازی افزایش داد.}, keywords_fa = {سوپرآلیاژ IN738LC,انحلال,حمام نمک,نرخ گرمایش,رسوبات گاماپرایم}, url = {https://www.foundingjournal.ir/article_79415.html}, eprint = {https://www.foundingjournal.ir/article_79415_3474e780757fdea3db2b271190342b7b.pdf} }