[1] Campbell J., Casting practice: the 10 rules of casting, Oxford, Butterworth-Heinemann, 2004.
[2] Masoumi M., Hu H., Hedjazi J., Boutorabi S.M.A., Effect of gating design on mold filling, AFS Transactions, 2005, 2, 1-12.
[3] Flender E. Sturm J., Thirty years of casting process simulation thirty years of casting process simulation, International Journal of Metalcasting, 2010, 10, 7-23.
[4] Vijaya Ramnath B., Elanchezhian C., Chandrasekhar V., Arun Kumar A., Mohamed Asif S., Riyaz Mohamed G., Vinodh Raj D. Suresh Kumar C., Analysis and optimization of gating system for commutator end, Procedia Materials Science, 2014, 6, 1312-1328.
[5] Divandari M., Campbell J., Oxide film characteristics of Al–7Si–Mg alloy in dynamic conditions in casting, Int. J. Cast Met. Res, 2004, 17, (3) 182–187.
[6] Sun Z., Hu H., Chen X., Numerical optimization of gating system parameters for a magnesium alloy casting with multiple performance characteristics, materials processing technology, 2008, 199, 256-264.
[7] Jain P.L., Principles of Foundry Technology, Tata McGraw-Hill, New Dlhi, 2003.
[8] Jafari H., Idris M. H., Ourdjini A., Farahany S., In situ melting and solidification assessment of AZ91D granules by computer-aided thermal analysis during investment casting process, Mater. Des, 2013, 50, 181-190.
[9] Dabade U.A., Bhedasgaonkar R.C., Casting defect analysis using design of experiments (DoE) and computer aided casting simulation technique, Proc. CIRP, 2013, 7, 616-621.
[10] Tsai D.C., Hwang W.S., Numerical simulation of solidification morphologies of Cu-0.6Cr casting alloy using modified cellular automaton model, Trans. Nonferrous Met. Soc. China, 2010, 20, 1072-1077.
[11] Heisser C., Simulation in modern quality managment systems, AFS, 03, 1-11.
[12] خسروی ر.، اصول طراحی سیستمهای راهگاهی و تغذیهگذاری چدنها، جامعه ریختهگران ایران, 1368.
[13] Rao T. V. R., Metal Casting Principles and Practice, K. K. Guta, New Delhi, 2003.
[14] Campbell J., Stop pouring start casting, Metalcasting, 2012, 12, 7-18.
[15] Chi Sun H., Sun Chao L., Analysis of Interfacial heat transfer coefficient of green sand mold casting for aluminum and tin-lead alloys by using a lump capacitance method, Heat Transfer, 2007, 129, 595-600.
[16] Geiger G. H , Poirier D. R., Transport phenomena in materials processing, United States of America: TMS. Minerals Metals Materials, Canada, 1994.
[17] ProCAST Users Manual, v2016.1, ESI Group, 2016.
[18] Hsu F. Y., Jolly M. R., Campbell J., Vortex gate design for gravity casting, Cast Metals Research, 2006, 19(1) 38-44.
[19] Campbell J., Complete casting handbook, Sec. Edition Ed., Butterworth-Heinemann, London, 2015.
[20] Yeh C. P., Hwang W. S., Lin C. H., Process design optimization through Numerical experimentation for a Brake Disc Casting, Materials Transactions, 2008, 49(6) 1372-1379.
[21] مدرسی ع.ر.، عیسی آبادی ق.، صفی خانی ع.، داودی س.ع.م.، مصطفی م.، بررسی ارتباط نوع طراحی راهباره بر تشکیل حفرات انقباضی در قطعه ریختگی چدن خاکستری مورد استفاده در صفحه فشار خودرو از طریق شبیهسازی با نرمافزار
ESI ProCAST، 1394، 107، 72-62 .
[22] Shabestari S. G., Ghoncheh M. H., Momeni H., Evaluation of formation of intermetallic compounds in Al2024 alloy using thermal analysis technique, Thermochimica Acta, 2014, 589, 174-182.
[23] Lu S.L., Xiao F. R., Zhang S. J., Mao Y. W., Liao B., Simulation study on the centrifugal casting wet-type cylinder liner based on ProCAST, Applied Thermal Engineering, 2014, 73, 512-521.
[24] Kor J., Chen X., Hu H., Multi-objective optimal gating and riser design for metal-casting, in IEEE International Symposium on Intelligent Control, Saint Petersburg, Russia, July-2009.
[25] Nandi T., Optimization of riser size of aluminium alloy (LM6) castings by using conventional method and computer simulation technique, Scientific & Engineering Research, 2011, 2, 2229-5518.
[26] خوشخرام ع.، دیواندری م.، بوترابی س. م. ع.، شبیهسازی اثر طراحی سیستمهای کفریز مختلف بر نحوه حرکت سیال و شرایط انجماد قطعه ریختگی، انتشارات جامعه ریختهگران، 1393، 32، 17-32.
