Additive ManufacturingNumerical simulation of solidification microstructure in selective laser melting additive manufacturing and studying the effect of process parameters on grains morphologies [Volume 3, Issue 4, 2019-2020, Pages 229-236]
Ageing treatmentEffect of directional solidification on the microstructure and mechanical properties of a 2th Generation Ni-base single crystal superalloy CMSX-4 [Volume 3, Issue 4, 2019-2020, Pages 187-199]
Al-FeInvestigating the Hot Tear Formation in Eutectic Al-Fe Alloys in Mushy Temperatures Ranges by Simulation of Solidification [Volume 3, Issue 2, 2019-2020, Pages 101-112]
Al-Mg2SiInvestigation of the Effect of Copper on Microstructural Modification and Quality Index of Al-15Mg2Si Composite [Volume 3, Issue 4, 2019-2020, Pages 217-227]
Al-Si alloysEffect of Stirring Temperature on the Morphology of Primary Si Particles, Hardness and Wear Behavior of Al-20wt.%Si Alloy Prepared by Semi-Solid Stir Casting [Volume 3, Issue 3, 2019-2020, Pages 151-162]
Al-Si-Mg alloysEffect of Magnesium Content on Functionally Graded Microstructure and Hardness of Centrifugally cast Al-20Si-XMg Composites [Volume 3, Issue 2, 2019-2020, Pages 55-66]
Aluminum ductile cast ironInvestigation of Microstructure and Hardness of upper Bainitic Austempered Aluminum Ductile Iron (Fe-3.4C-4.3Al-Mg) [Volume 3, Issue 2, 2019-2020, Pages 75-90]
Al-Zn alloysInvestigation of Oxide Film Characteristics in Al-Zn Melt by Oxide-Metal-Oxide Technique [Volume 3, Issue 3, 2019-2020, Pages 131-140]
AustemperingComparison of Wear Behavior of Ductile Iron in Austempered and Quenched-Tempered Conditions [Volume 3, Issue 3, 2019-2020, Pages 141-150]
B
Bainitic ferriteInvestigation of Microstructure and Hardness of upper Bainitic Austempered Aluminum Ductile Iron (Fe-3.4C-4.3Al-Mg) [Volume 3, Issue 2, 2019-2020, Pages 75-90]
C
CastingOptimization of Magnesium Solubility Factor in Production of Ductile Iron using Gating System Addition Method [Volume 3, Issue 1, 2019-2020, Pages 37-43]
CastingInvestigation of Microstructure and Chemical Composition of Mg-Ag-Ce-Zr Cast Alloy (QE22) [Volume 3, Issue 4, 2019-2020, Pages 237-245]
Casting simulationThe Effect of Inert Gas Injection Semisolid Process on the Structure and Hot Tearing Susceptibility of Al-4.3%Cu Alloy [Volume 3, Issue 1, 2019-2020, Pages 1-10]
Chemical compositionInvestigation of Microstructure and Chemical Composition of Mg-Ag-Ce-Zr Cast Alloy (QE22) [Volume 3, Issue 4, 2019-2020, Pages 237-245]
Chemical modificationInvestigation of the Effect of Copper on Microstructural Modification and Quality Index of Al-15Mg2Si Composite [Volume 3, Issue 4, 2019-2020, Pages 217-227]
CompositeInvestigating of Wettability Modification Methods on Microstructure and Mechanical Properties of Silicon Carbide/ Aluminum Composite Produced by Stir Casting [Volume 3, Issue 1, 2019-2020, Pages 21-28]
CompositeInvestigation of the Effect of Copper on Microstructural Modification and Quality Index of Al-15Mg2Si Composite [Volume 3, Issue 4, 2019-2020, Pages 217-227]
D
Deep ZeroThe Effect of Cooling Rate and Cryogenic Treatment on Microstructure and Hardness of IN738LC Cast Superalloy after Full Solution Annealing [Volume 3, Issue 1, 2019-2020, Pages 45-52]
Dendrite arm spacingEffect of Sample Diameter and Withdrawal Rate on Microstructure and Hot Tensile Behavior of Directionally Solidified PWA 1483 Superalloy [Volume 3, Issue 3, 2019-2020, Pages 175-185]
Dendritic structureModification Effect of Nickel on Tensile Properties and Microstructural Characterization of Al-12%Si-1%Mg-1%Cu Alloy [Volume 3, Issue 2, 2019-2020, Pages 113-121]
Directional SolidificationInvestigation of Heat Transfer Coefficients Effects in Directional Solidification of GTD111 Super-alloy [Volume 3, Issue 1, 2019-2020, Pages 11-20]
Directional SolidificationEffect of Sample Diameter and Withdrawal Rate on Microstructure and Hot Tensile Behavior of Directionally Solidified PWA 1483 Superalloy [Volume 3, Issue 3, 2019-2020, Pages 175-185]
Ductile ironOptimization of Magnesium Solubility Factor in Production of Ductile Iron using Gating System Addition Method [Volume 3, Issue 1, 2019-2020, Pages 37-43]
Ductile ironComparison of Wear Behavior of Ductile Iron in Austempered and Quenched-Tempered Conditions [Volume 3, Issue 3, 2019-2020, Pages 141-150]
E
Exposed BladeThe Effect of Cryogenic Treatment on the Rejuvenation of Exposed IN738LC Gas Turbine Blade [Volume 3, Issue 3, 2019-2020, Pages 163-174]
F
FluorapatiteMechanical Properties, Corrosion and Microstructure of Mg/2FA/0.3GNPs (wt.%) Hybrid Nanobiocomposite Produced by Mechanical Stir Casting and Remelting under Argon Pressure [Volume 3, Issue 4, 2019-2020, Pages 201-216]
G
Gama prime PrecipitatesThe Effect of Cooling Rate and Cryogenic Treatment on Microstructure and Hardness of IN738LC Cast Superalloy after Full Solution Annealing [Volume 3, Issue 1, 2019-2020, Pages 45-52]
Gamma prime precipitatesEffect of Sample Diameter and Withdrawal Rate on Microstructure and Hot Tensile Behavior of Directionally Solidified PWA 1483 Superalloy [Volume 3, Issue 3, 2019-2020, Pages 175-185]
Gating SystemOptimization of Magnesium Solubility Factor in Production of Ductile Iron using Gating System Addition Method [Volume 3, Issue 1, 2019-2020, Pages 37-43]
GISS semi-solidThe Effect of Inert Gas Injection Semisolid Process on the Structure and Hot Tearing Susceptibility of Al-4.3%Cu Alloy [Volume 3, Issue 1, 2019-2020, Pages 1-10]
GTD111DS AlloyInvestigation of Heat Transfer Coefficients Effects in Directional Solidification of GTD111 Super-alloy [Volume 3, Issue 1, 2019-2020, Pages 11-20]
H
HardnessEffect of Tungsten on the Hardness and Impact Resistance of Ni-Hard 4 Cast Iron [Volume 3, Issue 2, 2019-2020, Pages 91-99]
HardnessThe Effect of Cryogenic Treatment on the Rejuvenation of Exposed IN738LC Gas Turbine Blade [Volume 3, Issue 3, 2019-2020, Pages 163-174]
HardnessEffect of Stirring Temperature on the Morphology of Primary Si Particles, Hardness and Wear Behavior of Al-20wt.%Si Alloy Prepared by Semi-Solid Stir Casting [Volume 3, Issue 3, 2019-2020, Pages 151-162]
HardnessInvestigation of Microstructure and Chemical Composition of Mg-Ag-Ce-Zr Cast Alloy (QE22) [Volume 3, Issue 4, 2019-2020, Pages 237-245]
Heat treatmentEffect of Tungsten on the Hardness and Impact Resistance of Ni-Hard 4 Cast Iron [Volume 3, Issue 2, 2019-2020, Pages 91-99]
Heat treatmentComparison of Wear Behavior of Ductile Iron in Austempered and Quenched-Tempered Conditions [Volume 3, Issue 3, 2019-2020, Pages 141-150]
Heat treatmentInvestigation of Heat Treatment Methods on Microstructure and Hardness of Aluminum-Nickel Bronze Alloy (C95500) [Volume 3, Issue 4, 2019-2020, Pages 247-257]
Hot tearInvestigating the Hot Tear Formation in Eutectic Al-Fe Alloys in Mushy Temperatures Ranges by Simulation of Solidification [Volume 3, Issue 2, 2019-2020, Pages 101-112]
Hybrid nano-compositeMechanical Properties, Corrosion and Microstructure of Mg/2FA/0.3GNPs (wt.%) Hybrid Nanobiocomposite Produced by Mechanical Stir Casting and Remelting under Argon Pressure [Volume 3, Issue 4, 2019-2020, Pages 201-216]
I
Impact resistanceEffect of Tungsten on the Hardness and Impact Resistance of Ni-Hard 4 Cast Iron [Volume 3, Issue 2, 2019-2020, Pages 91-99]
Impeding pressuresDetermination of Critical Pressure and Impeding Pressure for Manganese Evaporation During the Induction Melting Process of Manganese-Nickel Alloys [Volume 3, Issue 2, 2019-2020, Pages 67-74]
IN738LC super alloyThe Effect of Cooling Rate and Cryogenic Treatment on Microstructure and Hardness of IN738LC Cast Superalloy after Full Solution Annealing [Volume 3, Issue 1, 2019-2020, Pages 45-52]
M
Melt holding timeEffect of Melt Holding Time on γ' Precipitates and Stress Rupture Properties of Rene 80 Superalloy [Volume 3, Issue 1, 2019-2020, Pages 29-36]
Microstructural modelingInvestigation of Heat Transfer Coefficients Effects in Directional Solidification of GTD111 Super-alloy [Volume 3, Issue 1, 2019-2020, Pages 11-20]
MicrostructureInvestigation of Microstructure and Chemical Composition of Mg-Ag-Ce-Zr Cast Alloy (QE22) [Volume 3, Issue 4, 2019-2020, Pages 237-245]
MicrostructureNumerical simulation of solidification microstructure in selective laser melting additive manufacturing and studying the effect of process parameters on grains morphologies [Volume 3, Issue 4, 2019-2020, Pages 229-236]
N
Nano-biocompositesMechanical Properties, Corrosion and Microstructure of Mg/2FA/0.3GNPs (wt.%) Hybrid Nanobiocomposite Produced by Mechanical Stir Casting and Remelting under Argon Pressure [Volume 3, Issue 4, 2019-2020, Pages 201-216]
Ni-Base super alloy CMSX-4Effect of directional solidification on the microstructure and mechanical properties of a 2th Generation Ni-base single crystal superalloy CMSX-4 [Volume 3, Issue 4, 2019-2020, Pages 187-199]
Ni-Hard 4 Cast IronEffect of Tungsten on the Hardness and Impact Resistance of Ni-Hard 4 Cast Iron [Volume 3, Issue 2, 2019-2020, Pages 91-99]
Ni Super-alloysInvestigation of Heat Transfer Coefficients Effects in Directional Solidification of GTD111 Super-alloy [Volume 3, Issue 1, 2019-2020, Pages 11-20]
O
Oxide filmInvestigation of Oxide Film Characteristics in Al-Zn Melt by Oxide-Metal-Oxide Technique [Volume 3, Issue 3, 2019-2020, Pages 131-140]
P
Primary Si particlesEffect of Stirring Temperature on the Morphology of Primary Si Particles, Hardness and Wear Behavior of Al-20wt.%Si Alloy Prepared by Semi-Solid Stir Casting [Volume 3, Issue 3, 2019-2020, Pages 151-162]
Process windowInvestigation of Microstructure and Hardness of upper Bainitic Austempered Aluminum Ductile Iron (Fe-3.4C-4.3Al-Mg) [Volume 3, Issue 2, 2019-2020, Pages 75-90]
PWA 1483 superalloyEffect of Sample Diameter and Withdrawal Rate on Microstructure and Hot Tensile Behavior of Directionally Solidified PWA 1483 Superalloy [Volume 3, Issue 3, 2019-2020, Pages 175-185]
Q
QE22 Mg-Ag-Ce-Zr alloyInvestigation of Microstructure and Chemical Composition of Mg-Ag-Ce-Zr Cast Alloy (QE22) [Volume 3, Issue 4, 2019-2020, Pages 237-245]
Quality indexInvestigation of the Effect of Copper on Microstructural Modification and Quality Index of Al-15Mg2Si Composite [Volume 3, Issue 4, 2019-2020, Pages 217-227]
Quench and temperComparison of Wear Behavior of Ductile Iron in Austempered and Quenched-Tempered Conditions [Volume 3, Issue 3, 2019-2020, Pages 141-150]
R
RejuvenationThe Effect of Cryogenic Treatment on the Rejuvenation of Exposed IN738LC Gas Turbine Blade [Volume 3, Issue 3, 2019-2020, Pages 163-174]
Rene 80 superalloyEffect of Melt Holding Time on γ' Precipitates and Stress Rupture Properties of Rene 80 Superalloy [Volume 3, Issue 1, 2019-2020, Pages 29-36]
Residual segregation indexCalculating the Elemental Diffusivities During Homogenization of as-cast Inconel 718 Superalloy [Volume 3, Issue 3, 2019-2020, Pages 123-129]
S
Semi-Solid CastingEffect of Stirring Temperature on the Morphology of Primary Si Particles, Hardness and Wear Behavior of Al-20wt.%Si Alloy Prepared by Semi-Solid Stir Casting [Volume 3, Issue 3, 2019-2020, Pages 151-162]
SiC wettabilityInvestigating of Wettability Modification Methods on Microstructure and Mechanical Properties of Silicon Carbide/ Aluminum Composite Produced by Stir Casting [Volume 3, Issue 1, 2019-2020, Pages 21-28]
Silicon carbide -Aluminum compositeInvestigating of Wettability Modification Methods on Microstructure and Mechanical Properties of Silicon Carbide/ Aluminum Composite Produced by Stir Casting [Volume 3, Issue 1, 2019-2020, Pages 21-28]
SimulationInvestigating the Hot Tear Formation in Eutectic Al-Fe Alloys in Mushy Temperatures Ranges by Simulation of Solidification [Volume 3, Issue 2, 2019-2020, Pages 101-112]
Single crystal solidificationEffect of directional solidification on the microstructure and mechanical properties of a 2th Generation Ni-base single crystal superalloy CMSX-4 [Volume 3, Issue 4, 2019-2020, Pages 187-199]
SolidificationInvestigating the Hot Tear Formation in Eutectic Al-Fe Alloys in Mushy Temperatures Ranges by Simulation of Solidification [Volume 3, Issue 2, 2019-2020, Pages 101-112]
SolidificationNumerical simulation of solidification microstructure in selective laser melting additive manufacturing and studying the effect of process parameters on grains morphologies [Volume 3, Issue 4, 2019-2020, Pages 229-236]
Solution FactorOptimization of Magnesium Solubility Factor in Production of Ductile Iron using Gating System Addition Method [Volume 3, Issue 1, 2019-2020, Pages 37-43]
Solution heat treatmentThe Effect of Cooling Rate and Cryogenic Treatment on Microstructure and Hardness of IN738LC Cast Superalloy after Full Solution Annealing [Volume 3, Issue 1, 2019-2020, Pages 45-52]
Stress Rupture propertiesEffect of Melt Holding Time on γ' Precipitates and Stress Rupture Properties of Rene 80 Superalloy [Volume 3, Issue 1, 2019-2020, Pages 29-36]
SuperalloysCalculating the Elemental Diffusivities During Homogenization of as-cast Inconel 718 Superalloy [Volume 3, Issue 3, 2019-2020, Pages 123-129]
T
T6-treatmentModification Effect of Nickel on Tensile Properties and Microstructural Characterization of Al-12%Si-1%Mg-1%Cu Alloy [Volume 3, Issue 2, 2019-2020, Pages 113-121]
TungstenEffect of Tungsten on the Hardness and Impact Resistance of Ni-Hard 4 Cast Iron [Volume 3, Issue 2, 2019-2020, Pages 91-99]
V
VIM furnacesEffect of Melt Holding Time on γ' Precipitates and Stress Rupture Properties of Rene 80 Superalloy [Volume 3, Issue 1, 2019-2020, Pages 29-36]
W
WearComparison of Wear Behavior of Ductile Iron in Austempered and Quenched-Tempered Conditions [Volume 3, Issue 3, 2019-2020, Pages 141-150]
WearEffect of Stirring Temperature on the Morphology of Primary Si Particles, Hardness and Wear Behavior of Al-20wt.%Si Alloy Prepared by Semi-Solid Stir Casting [Volume 3, Issue 3, 2019-2020, Pages 151-162]
