[1] Hirt G., Kopp R., Thixoforming: Semi-Solid Metal Processing, John Wiley & Sons, 2009 4-7.
[2] Wannasin J., Martinez R.A., Flemings M.C., A novel technique to produce metal slurries for semi-solid metal processing, Solid State Phenomena, 2006, 116-117, 366-369.
[3] Stangeland A., Asbjørn M.O., Nielsen Ø., M’Hamdi M., Eskin D., Development of thermal strain in the coherent mushy zone during solidification of aluminum alloys, Metallurgical and Materials Transactions A, 2004, 35(9) 2903-2915.
[4] Lashkari O., The Rheological Behavior of Semi-Solid A356 Alloy, Doctoral dissertation, Université du Québec à Chicoutimi, 2006.
[5] Lemieux A., Langlais J., Bouchard D., Chen X.G., Effect of Si, Cu and Fe on mechanical properties of cast semi-solid 206 alloys, Transactions of Nonferrous Metals Society of China, 2010, 20(9)1555-1560.
[6] Wannasin J., Schwam D., Yurko J.A., Rohloff C., Woycik G., Hot tearing susceptibility and fluidity of semi-solid gravity cast Al-Cu alloy, In Solid State Phenomena Trans. Tech. Publications, 2006, 116, 76-79.
[7] Bray J.W., Properties and selection: Nonferrous alloys and special purpose materials, ASM Metals Handbook, 1990, 92.
[8] Lin S., Aliravci C., Pekguleryuz M.O., Hot-tear susceptibility of aluminum wrought alloys and the effect of grain refining, Metallurgical and Materials Transactions A, 2007, 38(5) 1056-1068
[9] Birol Y., Thixoforming of EN AW-2014 alloy at high solid fraction, Journal of Materials Processing Technology, 2011, 211(11) 1749-1756.
[10] Gonçalves M.C., Martins M.G., Misiolek W.Z., Van Geertruyden W.H., Homogenization and hot workability of alloy AA2014. In Materials Science Forum, Trans Tech Publications, 2002, 396, 393-398.
[11] Ghoncheh M.H., Shabestari S.G., Abbasi M.H., Effect of cooling rate on the microstructure and solidification characteristics of Al2024 alloy using computer-aided thermal analysis technique, Journal of Thermal Analysis and Calorimetry, 2014, 117(3) 1253-1261.
[12] Malekan M., Shabestari S.G., Computer-aided cooling curve thermal analysis used to predict the quality of aluminum alloys, Journal of Thermal Analysis and Calorimetry, 2011, 103(2) 453-458.
[13] Payne R.T., The purification of inert gases to high purity, RD Mathis Company.
[14] D’Elia F., A Study of Hot Tearing during Solidification of B206 Aluminum Alloy, Doctoral dissertation, Ryerson University, 2015.
[15] Pekguleryuz M.O., Lin S., Ozbakir, E., Temur D., Aliravci C., Hot tear susceptibility of aluminium–silicon binary alloys, International Journal of Cast Metals Research, 2010, 23(5) 310-320.
[16] Rikhtegar F., Shabestari S.G., Investigation on solidification conditions in functionally Si-gradient Al alloys using simulation and cooling curve analysis methods, Journal of Thermal Analysis and Calorimetry, 2014, 117(2)721-729.
[17] Abdi M., Shabestari S.G., Semi-solid slurry casting using gas induced semi-solid technique to enhance the microstructural characteristics of Al-4.3Cu alloy, In Solid State Phenomena, Trans. Tech. Publications, 2019, 285, 253-258.
[18] Abdi M., Shabestari S.G., Effect of gas-induced semisolid process on solidification parameters and dendrite coherency point of Al–4.3Cu alloy using thermal analysis, Journal of Thermal Analysis and Calorimetry, 2019, 1-10 (in press).
[19] Chen Q., Zhao Z., Chen G., Wang B., Effect of accumulative plastic deformation on generation of spheroidal structure, thixoformability and mechanical properties of large-size AM60 magnesium alloy, Journal of Alloys and Compounds, 2015, 632, 190-200.
[20] Bolouri A., Shahmiri M., Cheshmeh E.N.H., Microstructural evolution during semisolid state strain induced melt activation process of aluminum 7075 alloy, Transactions of Nonferrous Metals Society of China, 2010, 20(9)1663-1671.